Casing Design - Excel Sheet

These steps of casing design for stress and tension for different loads comes after working with pore pressure and fracture pressure gradient to get assumptions with casing setting depths     

Within the window between not have losses or to have kick as well not fracture the formation

There  is a detailed example demo on 9 5/8 as guide  read it carefully, u have to be fully focused, every this is here , just give it some focus , I escaped some details. then two detailed csg design .       

Escaped minor details u can google it, just for sack of not to confuse you, sure you should be with petroleum and engineering back ground basically.       

u can make use of drilling formula and baker Hughes drilling data book.     

Please don’t change anything, and share as many as you can so people can benefit from, basically did this as I did not find any one in colleague to do this for me!       

But always give the credit to the idea creator. Hope you can make use of that

Casing Design Overview – Overall Process of How To Do Casing Design in Oil and Gas Industry
Casing Design Objectives

The items below are design objectives for well constructions which drilling engineers must consider.
Design must meeting production strategies.
Design must provide mechanical integrity based on anticipated load cases which will be encounter during life time of the well.
Cost of well must be economic.
Design must provide ways to be able to plug and abandon the well at the end of wells life. These objectives are generic and your wells may have additional objectives based on business needs.
Data Required for Casing Design
The following items are information require for casing design.
Production Information
o Type of packer fluid
o Density of packer fluid
o Type of reservoir fluid
o Expected flow rate, pressure, temperature of the well
o Sour gas (H2S, Co2)
o Maximum production load case
o Completion strategies
Geological Data
o Pore pressure
o Fracture pressure
o Formation temperature
o Formation type and structure
o Plan for logging programs
o Location of problematic zones as possible loss zones, high permeable zones, unstable zones, shallow gas hazard, fresh water zones, sour gas (H2S, CO2) zones, etc
Directional Data
o Geologic targets
o Surface location
o Anti-Collision issue
Production plan
o Size of casing and tubing met required production rate
o Completion equipment (packer, SCSSV, gas lift valves, etc) planned to run into the well
Government regulation
o Each country has different requirement for drilling oil wells.
Equipment supply and logistics
o International or local suppliers for casing
o Logistics and tax for equipment
Design Phases

There are two phases of design. The first on is a preliminary design and the second one is a detailed design.
Preliminary Design Phase

After gathering information required, you will do the first phase of casing design. The preliminary design will give you all scopes of the project (well construction plan). The following scopes are results from this phase.
Casing setting depth and number of strings – The following factors used to determine casing setting depths.

o Pore pressure and fracture gradient – Based on the pore pressure and the fracture gradient of the well, you will be able to determine how many strings required and where each string needs to be set. There are two approaches which are top down design and bottom up design. We will go into details of this topic later on.

o Differential sticking zones – potential sticking formations should be cased off before going deeper because the deeper depth requires higher mud weight which will result in more serious of pipe stuck issue.

o Wellbore stability – this is the same concern as the differential sticking. Right type of mud and weight will minimize this issue.

o Formation pressure / fracture gradient prediction uncertainty – drilling into unknown areas has a lot of uncertainty regarding pore pressure / fracture gradient prediction. Therefore, additional string must be considered to run as a contingency string.

o Directional concern – Typically casing is set after a building section of the well in order to mitigate a key seat issue while drilling deeper.
Drilling fluid program – drilling fluid weight is the most critical factor in the casing design. Mud weight should be sufficient enough to drill to planned depth without fracturing formation at shallower depth. Moreover, drilling mud for each section needs to meet drilling objectives as hole cleaning, wellbore stability, formation evaluation, minimizing formation damage, etc.
Drilling equipment needed – drilling equipment is one of the factors which need to take into account carefully. You should ask yourself about drilling equipment:

o What is the specification of the drilling rig?

o Can the rig work with the casing plan?

o Does the rig have enough power to provide hydraulic power to downhole tool, clean the hole, etc?

o Do we have the well control equipment fit for the operation?

o What size of downhole tool do you need to drill the well?
Production equipment – equipment required for production which you need to consider is listed below;

oType, size, grade, etc of production tubing

oCompletion equipment as sub surface safety valve, gas lift valve, submersible pump, down control valve, etc

o Gravel pack and frac pack

Especially, nowadays many companies tend to run smart completion in order to prolong well life and optimize well production. This will require a lot of clearance between completion string and production tubing. It might affect the casing size big time.
Formation evaluation – this relates to tool size and drilling fluid used in that section which you need to evaluate reservoir.
Top of Cement (TOC) – TOC will have effect on load design and typically TOC design is based on the following criteria;


o Regulatory requirement


o Zonal isolation


o Formation strength


o Buckling


o Pressure build up in the annulus
Detailed Design Phase


In this phase, engineers will go into detailed calculations in order to select casing/tubing (size, grade, connection, etc) for all strings based on the preliminary design. The engineers will design each string of pipe by using design criteria which consist of design factors and load cases.


Load cases for casing design are as follows;
Burst load
Collapse load
Production load
Drilling load
Running and cementing load
Axial load '' Tri Axial if needed ''


Oil Well Casing Design Excel Sheet # Free
it is simple and easy to use
Please feel free to contact me for any details
you will need casing-and-tubing data catalogue
Engineering Material Reference - Texas A&M University , Drilling Engineering
Drilling Formula Website: Casing Design overview 
Design Sheet including Collapse , Burst , Axial Load By Amr Haggag


Created 2011 - updated 2018


Originally made by Amr Ibrahim Haggag ,

Petroleum Engineer , Cairo University - 1999

for any question , and I will reply as I can

aimo.haggag@gmail.com

Follow link to download

https://bit.ly/39mcyvY  or here 
https://drive.google.com/file/d/1YE_BmtV5dZducXm-96m9K2aahvVWtPhP/view?usp=sharing 
------------------------------------------
Design Materials